english contents

In the english content section we provide content for our international readers.

28. Jun. 2018 | 06:23 Uhr
Rubber reinforced with textile cords

Finite Element Models for textile reinforced Rubber Components

The bellows as key component of air springs is made from rubber reinforced with textile cords.Weiterlesen...

27. Jun. 2018 | 07:03 Uhr
Silikonverarbeitung mit einer 8 mm kleinen Einheit

DKT 2018: Cool way of Silicone Processing

Dr. Boy zeigt auf der Ausstellungstagung in Nürnberg die Verarbeitung von Elastomeren und Sili-konen auf zwei Spritzgießautomaten, darunter eine Anwendung mit zwei Flüssigsilikon-Komponenten.Weiterlesen...

26. Jun. 2018 | 06:25 Uhr
NEU_Fig1 Experimental setup of high-pressure capillary rheometer test.png
Rheometric analyses are performed with a high-pressure capillary rheometer

Investigation of Wall Slippage in Silicone Rubber Compound by means of High-pressure Capillary Rheometer

Compared to organic rubber, silicone rubbers have a lower viscosity and a stronger structural viscosity.Weiterlesen...

25. Jun. 2018 | 06:21 Uhr
Kein Bild vorhanden
Mixing Room Solutions

DKT 2018: Mixing Room Solutions

HF Mixing Group´s strategy clearly has a focus for mixing room systems all delivered out of one hand.Weiterlesen...

21. Jun. 2018 | 06:50 Uhr
Sofya Dedova_Leibniz Institut_Figure8
A new Biaxial Tester

Biaxial testing System for high static and dynamic Loading of Elastomers and its Applications

For the investigation of elastomers under near-realistic loading, a new Biaxial Tester was designed and tested.Weiterlesen...

20. Jun. 2018 | 09:35 Uhr
Ikeda Fig. 2a
Spectroscopy of a sulfidic structure of isoprene rubber (IR)

Effect of solvent Extractions on a linear Combination fitting in sulfur K-edge X-ray Absorption near edge structure Spectroscopy for Sulfur cross-linked Rubber

Necessity of solvent extractions in the linear combination fitting method of sulfur K-edge X-ray absorption near edge structure (S-XANES) spectroscopy is described for evaluation of a sulfidic structure of isoprene rubber (IR) vulcanizate prepared using N-(1,3-benzothiazol-2-ylsulfanyl)cyclohexanamine as an accelerator, and zinc oxide and stearic acid as activators.Weiterlesen...

20. Jun. 2018 | 06:59 Uhr
tire tread
Tailor made Silica/Silane-Systems

Precipitated Silica – Morphology Control

Precipitated silica, especially in combination with bifunctional organosilanes, is one of the most important active filler, filler system respectively, that is used in the rubber industry and especially in passenger car tire tread compounds. Despite the fact that there are already many different silica having a broad range of different specific surface areas, the variety of cluster sizes in the nanometer range is rather low in contrast to the broad range of available carbon black structure variations.Weiterlesen...

20. Jun. 2018 | 06:26 Uhr
Yuanli_Figure 3
The effect of one stage isothermal and two-stage non-isothermal cure on crosslink density, crosslink structure

Investigations on isothermal and two-stage non-isothermal cure of unfilled NR, Nd-IR and S-SBR Compounds

The effect of one stage isothermal and two-stage non-isothermal cure on crosslink density, crosslink structure and stress-strain behavior of unfilled NR, Nd-IR and S-SBR compounds has been investigated.Weiterlesen...

19. Jun. 2018 | 08:13 Uhr
Blume_Bild 3
Abrasion resistance of silica filled passenger car tire tread compounds

Void Volume Measurement - an alternative Approach to Determine the Initial Structure of Silica

To improve the abrasion resistance of silica filled passenger car tire tread compounds a good dispersion and distribution of the silica in the rubber matrix is required. From the literature it is known that the structure of fillers affects the dispersion process.Weiterlesen...

18. Jun. 2018 | 06:15 Uhr
Bremsbacke, PC, Silikon,
Kompetenz und Erfahrung in der LSR-Verarbeitung

Multi-component injection moulding of hard/soft combinations

Arburg präsentiert „live“ auf der DKT 2018 eine anspruchsvolle Mehrkomponenten-Anwendung mit einem elektrischen Allrounder 470 A. Ausgestattet mit einer externen Kolben-Spritzeinheit, fertigt die Maschine der Baureihe Alldrive Verstellbremsen aus Thermoplast (PBT) und Flüssigsilikon (LSR) für die Automobilindustrie.Weiterlesen...